If you don’t have a bow maker, then this 3 Loop Hand Bow for wreath is the bow for you! 3 loop bows add a ton of movement to your wreaths, and this option is perfect for a quick bow without any fuss. You’re sure to love how simple this bow is to create and add to any wreath.
How to Craft a Gorgeous Three Loop Hand Bow For Wreath
I love my bow maker, but sometimes it’s in the other room or I just don’t feel like pulling it out. Maybe you don’t have one! Then a hand bow is perfect. I love how simple these bows come together and add so much to a wreath.
3 loop bows are perfect to add a lot of movement to your wreaths. I love a large bow with a lot of movement, and 3 loop bows are a fun way to do that. They are also very interesting to the eye because they are different from a traditional bow.
The best part about this bow is that it comes together in a snap. It’s perfect for a quick bow to finish up a simple wreath, or as a final touch on a more intricate wreath. It’s so versatile and one of my go-to bows.
Print
Directions
- Start by cutting a dovetail, or V cut, in your ribbon and measuring your first tail. I chose to make mine 24” for a nice long tail with a lot of movement.
- At the 24” mark, hold your ribbon tightly and create a twist by twisting your right hand backward and your left hand forward. Hold that twist between your thumb and forefinger.
- Create your first loop, as big as you’d like it. I decided to make mine about 6”. When your loop is created, twist your ribbon like you did earlier, then hold that loop with your same thumb and forefinger.
- Repeat these steps to create 2 more loops, one symmetrical to your first, then one on the same side as your first. You’ll end up with 2 loops on one side and 1 loop on the other.
- Cut your second tail. I cut mine a little shorter than my first, but you could cut it at 24” as well and have two long tails.
- Thread your cable tie behind your ribbon, behind the part of the ribbon you were holding with your thumb and forefinger. Loop the cable tie around and tighten loosely. Shift the cable tie to the back, then tighten.
- Cut a piece of ribbon that is about 10” long. If your ribbon is wider than 1”, cut your ribbon in half. Tie this small piece around the center of your bow, tying them tightly in the back, to cover your cable tie.
- Floof your loops and arrange your loops and tails as you’d like them to lay, and you’re ready to go!
TIPS AND TRICKS
- Change your ribbons to make bows that match whatever type of wreath you are creating. If you are using flowers, attach a flower to the center of the bow for a fun look. Make your wreath your own!
- If you’d rather use wire than a cable tie, 18 gauge works perfect for bows.
- I used a wide ribbon for this bow, a 2.5” jute wire-edged ribbon, and I think that works best. But you are free to use this same bow with any type of ribbon you’d like to match your wreath. Your bow will be more floppy if you use a ribbon that is not wire-edged.
How do you attach a bow to a wreath?
I love using cable ties. Before I tighten my first cable tie all the way, I add a second perpendicular cable tie to the back of my bow. This second tie allows me to attach the bow to the wreath. If you are using wire, you can do the same thing and add a second piece of wire to the back of the bow. Simply weave this through the wreath and tighten, and you’re ready to go.
Can I use multiple bows on my wreath?
Absolutely! It’s your wreath. If you think multiple smaller bows would be cute, go for it! I would use a narrower ribbon to make a smaller bow, but using a wide ribbon with small loops might be a fun look too. Adjust the ribbons to make it work with your wreath, and create a wreath that you love!
Are you searching for a unique DIY project this Halloween? Look no further than the Frankie Centerpiece Kit, perfect for adding a personalized and cute spooky touch to your Halloween decor. This DIY arrangement kit blends creativity with simplicity, making it an ideal craft for all skill levels.
DIY Frankie Centerpiece for Halloween Home Decor
Crafting your centerpiece is straightforward and enjoyable. You’ll need some basic tools like styrofoam, wire cutters, scissors, and hot glue. Begin by setting styrofoam inside the bucket, strategically place the twig sprays and, and use the eyeball picks for a finishing touch of flair.
Let me show you how to create your own DIY Frankenstein Halloween Centerpiece that is a cute not spooky decoration for Halloween. Mixing your spooky decorations with old and new gives you fun times spent crafting together now while reminiscing about the Halloweve of yester years. It’s a wonderful way to start a family tradition or simply enjoy some seasonal crafting magic.
Ingredients
Directions
- Start by finding cutting the styrofoam so it is nestled inside of the Green Frankenstein Bucket so that it sits nicely inside and glue down. I like to use both Gorilla Glue and Hot Glue to really secure it for both now and long term.
- Cut Black Garland Base into small sections and set your base, spreading for maximum coverage.
- Prep your picks by grabbing your Purple Green Orange Felt Ball Twig Sprays. Sseparating them into smaller picks. You can also twist the black chenille around your finger to create a fun effect.
- Trim your Glitter Eye Ball Picks and add to the stryofoam. Be sure to space them for the best visual display.
- Cut and prep the White Black Chenille Curly Stems add some dimension to them by curling with your fingers to really give them life.
- Stem back and look at your your centerpiece. Are thier bald or blank spaces? Fluff you black garland to fill and use the wires in your products from Keleas.com to really get the pieces where you want them.
- Grab one of your Glitter Curly Velvet Ball Picks and trim the stem down to a couple of inches. Fluff out your pick, and then place it to the left of your bow, tucking it behind the bow to have it peek out from behind it.
